How to make a wood frame

how to make a wood frame

How to make wood frames! Step by Step!

Making a Wooden Picture Frame: One of the first projects many beginner woodworkers build is a picture frame. I've been making sawdust for a few years now, but I can't recall ever having made one myself. So for Christmas just gone, I decided to make one for my wife as a gift.I too. Dec 04, Cut your middle main boards however long you want. Then you are going to want to cut two of the skinny wood so it matches the height of the frame. Keeping it all together you measure across the two pieces of wood you have cut and the inside piece to find the length and cut two more pieces for the top and bottom.

One of the first projects many beginner woodworkers build is a picture frame. I've been making sawdust for a few years now, but I can't recall ever having made one myself. So for Christmas just gone, I decided to make one for my wife as a gift. I took a few how to make a wood frame along the way so thought it might be fun to create another instructable from them; especially seeing how much good feedback I got for the last one.

Thanks for looking, feel free to leave any questions in the comments below and I'll do my best to answer them. If you're so inclined, I have more about this project and many others on my website, www. The wood I chose for this frame was a length of a very dense, red coloured hard wood. I assume red gum or maybe even jarrah but I've very little experience with hard woods so I could be way off.

I can tell you that how to make a wood frame was extremely heavy and hard. I picked it up from a house renovation I worked on, I think it had been an outside step which led onto a decking. The first thing I did was rip it down on my table saw into the required widths.

In my case, about 80mm wide and 16mm thick. As you can see, the wood was so dense my saw struggled a fair bit and ended up burning them on one side. Burn marks aren't really a big problem, they just look bad. Now I don't have a thicknesser, jointer or even a decent handplane so my options were limited for this step. I needed to smooth the lengths out, remove the burn marks and get them as flat as possible.

I decided to use my larger belt sander for this task. Using 80grit paper I ran each length over the belt until I was left with a flat surface. I was a bit worried that using the rough paper would create valleys and dips in the wood, how to make a wood frame seeing as it was so dense the machine could really only take off the very outer how to make a wood frame unless I held it in place for a while.

I was careful to always keep it flat and level and just took my time. Once I was finished sanding them, I used an old paint scraper as a cheapo cabinet scraper. It worked wonderfully, you just make short, repetitive scraping motions towards you, and watch the grain completely flatten out and become almost glass smooth.

There are videos on youtube and chapters of books devoted to caring for and maintaining what are the characteristics of third world countries, not being a professional, I ignored them all.

I found that if I scraped for a bit, then performed the same motion on the reverse side of the blade on top of sandpaper, that I could easily sharpen it and get consistent results. I placed each length on my table saw mitre sled and made the angled cuts. The sled was made following along from this design from Jay Bates. It is a simple build that takes little time but provides great results. Exactly the same. Or your frame will not be square no matter what you do.

If I cut one length on the left of the blade, I make sure that I cut the mating length on the right side of the blade. This way, even if my jig is slightly out of alignment, the two lengths will still combine to create a perfect 90 degree angle. Once they were cut, I ran them through the table saw and cut out a rebate nascar valley is the nickname of what state all 4 pieces for the MDF backing board and plexiglass to sit in.

I also used my router table to put a slight roundover on the inside of the frame, and a chamfer on the outside. I cheated here and used a single kreg pocket hole screw in each corner with glue to help hold the frame together.

Though to be honest, this system worked out great anyway, it is strong, square and the joints lined up perfectly. Once it was all dry, I measured the inside dimensions and cut a 3mm board of MDF and plexiglass to how to make a wood frame. They sit in the rebate and are held in with some small nails that I tapped what is bdc in abap on an angle behind them.

Looking around my garage, the only clear coat varnish I had on hand was this one by Feast Watson You can see in the before and after photos just what a difference it made to the wood, like night and day really. All that was left was to add the photo which I designed in photoshop and put a hook on the back. Reply 6 years ago on Introduction. Thanks seamster, I will have to get on to that spline jig though, I can't very well use pocket holes on all my future frames I think.

Introduction: Making a Wooden Picture Frame. By TheWoodfather www. More by the author:. About: Hi there! I'm Mario, from thewoodfather.

I've been working wood for years, but it's past time that I made the effort to move from the DIY woodworker I am now, to the high quality, furniture making woodwor More About TheWoodfather . I fully intended on using a spline jig to help make it more secure but I just ran out of time. I do love my kreg pocket hole jig. I also took this time to sand and scrape the timber again, preparing for a finish.

I got lucky with this piece of scrap wood, it really is a beautiful, rich colour to look at. I think it looks fantastic and my wife loved it so that's what really matters. Making a frame is a fairly simple woodworking task, not sure why I put it off for so long! Did you make this project? Share it with us! I Made It! Giant Saw Blade Table! Reply Upvote.

This is a great looking frame, and a very nicely put together guide. The ability to build a nice picture frame is an under-appreciated skill! TheWoodfather seamster Reply 6 years ago on Introduction. I think you might be "rabbet" rather than "rebate". TheWoodfather akwhitacre Reply 6 years ago on Introduction.

Step 1: Prep the Timber

Crafts and DIY that are fast and easy. Glue gun, vinyl, sewing, painting I have posted random projects using these frames for the past few monthsand every time I do I get askedHOW to make them! And they are so easy I literally made a few weeks ago! That makes them the greatest present ever! I create a wood frame round 2the chunky frame! See it here! I even hopped on facebook live to show you step by step! Really cheapand you can get about 2 whole frames 8 pieces from each one!

You will want to try the flattest piece of wood that looks smooth. Some of those small boards can be totally splintery and curvy! There is whole side of different sizes. So I like 3 of the 4 inch boards. This one is about 18 inches by 26 inches! I buy 6 feet longbecause I can fit it in the back of my 4 runner. But they have 10 feet long boards! If you buy one of the skinny boards for the frame and one 6 inch wide boardyou are going to get a least two frames unless you go BIG! ANDdid you know that Home Depot cuts wood for you?

So if the cutting part scares you than take a measuring tape and pencil there and have them get ur done. Just measure out and cut! Cut your middle main boards however long you want. Then you are going to want to cut two of the skinny wood so it matches the height of the frame. Keeping it all together you measure across the two pieces of wood you have cut and the inside piece to find the length and cut two more pieces for the top and bottom.

Life is too short for that crap! I lay out to find the best sides and.. I love the look of stain. I thought I would share some of my favorite colors! Espresso from general finishes. Classic gray from Minwax. I used this. But it works so quickly! I start with the pieces of the frames that are flushthat way you can match up the larger piece exactly. For each piece of wood, it needs two nails. If you do one nail the board can move while you are nailing in the other pieces and make it wonky!

See the blue arrows? That is where you will need to add nails. It connects the frames together! So you can just leave those nail holes! No need to putty! When you are done the back should be totally flush. If you want to hangI totally recommend these sawtooth picture hangers! Just hammer them in! Sand the edges of the frame. Sometimes I add some brown to the light colors. Hot glue on some fun letters. Vinyl is so easy to add a fun saying!

Grab the cut file for this one here. This one is is floracraft foam and vinyl! This one is made out of foam core board! This pumpkin was from a store! Just hot glued it on! You can add a clip and make it so they can swap out pictures. If you want to learn how to use vinyl as stencil to get fun distressed signs go here. I even watercolored onto one! We had a craft nightand partnered up with Any way you cut it my neighbor!!!

Check out how colorful and unique each one is! I also wanted to share Virginia from Fynes Designs.. They are alllll so cute! A girl and a glue gun is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.

Your IP address and user-agent are shared with Google along with performance and security metrics to ensure quality of service, generate usage statistics, and to detect and address abuse. A girl and a glue gun Crafts and DIY that are fast and easy. How to make wood frames! Step by Step! December 4, By Kimbo. About the Author Latest Posts About Kimbo Kimbo blogs at A girl and a glue gun--where she puts her hot glue gun to good use as well as her vinyl cutter and sewing machine She loves all crafts and is thrifty the nice way to say she's cheap So she is constantly trying to come up with fast and easy projects that won't break the bank!

She lives in Idaho with her hot husband and 3 kiddos. Filed Under: decorating , paint , wood. Visit Kimberly West a girl and a glue gun 's profile on Pinterest. Return to top of page.

4 thoughts on “How to make a wood frame

  1. Most videos I have seen on AD, most female celebs are not wearing shoes inside their houses when showing it.

Add a comment

Your email will not be published. Required fields are marked *