How to adjust hid headlights

how to adjust hid headlights

How to Adjust HID Headlights

Open the hood and go to the rear of the headlight assembly. At the top and center of the headlight will be a small adjusting screw that controls the light's vertical axis. Use a screwdriver to adjust this until the light hits the desired spot. Along one of the sides will . Make the necessary adjustments with the lights still on while watching the light beams on the wall and your marks. Turning the top adjusting screws in a clockwise direction will raise the beam while counterclockwise turn will lower it. Turning the side adjuster screws will adjust the .

HID Kits. HID Replacement Bulbs. Adjusting the headlights is a how to adjust hid headlights task. It does not take a mechanic to get it done. All you need are a few tools and a few minutes. Philips screwdriver Masking tape. The best time to do it, of course, is at night. Find the adjusting screws of the headlights It is better to find these screws before turning on the light This will allow you to touch the headlights before they warm up. Each headlight has a horizontal and a vertical screws which have small springs behind them.

Some vehicles come equipped with a small level attached to the top of the headlight under the hood. It helps you get an accurate adjustment.

Park your vehicle on level ground with the headlights near a garage door or wall. A good distance is feet away from the wall or door. The location must be perfectly level and flat at a distance of 10 to 25 feet away from the door or wall.

Switch on the low headlight beams and mark the horizontal and vertical centerlines of each headlight beams on the wall using masking tape. The marking will tell you where exactly the headlight beams should be centered from a distance.

Move the how to adjust hid headlights back about 10 to 25 feet away from the garage door or the wall. Keep the headlights on the low beam setting.

Use the markings you made on the wall or garage door to, check where the light shines and see if the centerlines still match up with the masking tape marks. If the centerlines of the two beams do not align with the tape marks, you can adjust one or both sides as needed. Make the necessary adjustments with the lights still on while watching the light beams on the wall and your marks.

Turning the top adjusting screws in a clockwise direction will raise the beam while counterclockwise turn will lower it. Turning the side adjuster screws will adjust the lights to the left or right. Continue the adjustments until the center of the light beams are aligned with the tape marks.

Then adjust the vertical alignment of both beams slightly below the marks on the wall. The low beams and high beams are connected to the same mechanism, so once the low beams are properly adjusted, the high beams will automatically be set.

Oh and don't forget to remove the masking tap from the garage door if it rains it is impossible to get the tape off of the door. Adjusting HID Headlights. About How to download linux os on windows 7. What is HID?

Relay Harness. Tools: Philips screwdriver Masking tape. Procedure: 1. The low beams and high beams are connected to the same mechanism, so once the how to adjust hid headlights beams are properly adjusted, the high beams will automatically be set Contact Us Email: superlumination cox.

HID Ballasts. How to adjust HID headlights Adjusting the headlights is a how to draw a line of best fit in excel task.

Installation Relay Harness.

Featured Videos

Nov 14,  · There is a hex (allen) socket on the side of the lights that you can turn to adjust the vertical position of the lamps. It's easiest to adjust at night in front of a garage door or wall. Park about 15 feet away and adjust the lights using a hex key with a screwdriver or ratchet. Apr 08,  · One of the headlights was aimed sky high so yo I didn't have much luck finding out how to do this online so I figured I'd post a video once I figured it out. One of the headlights was aimed sky. How to adjust and align Chevy Silverado Morimoto XB LED Headlights. How to adjust and align Toyota Tundra Morimoto XB LED Headlights. How to aim and adjust Ford F Morimoto XB LED Headlights. How to aim and align Ford F Morimoto XB Hybrid LED Headlights. How to aim and align Dodge Ram.

HID headlights provide a more powerful focus and long-lasting light beam than traditional headlight bulbs. These newer light bulbs are easily recognized by their blue tint and strong shine. Because of their strength, though, it is important to have them properly aligned. If a headlight is not adjusted in the correct manner, not only will your line of sight be diminished, but oncoming traffic my be blinded.

Luckily, fixing this problem isn't much more difficult than taking a few measurements and adjusting a few screws. Load the automobile with enough weight to approximate the normal nighttime driving weight. Weight will affect the angle of the light beams, so it is important that this is correct.

Things to consider are the trunk, back and passenger seats as well as having a partner sit in the driver's seat representing you. Pull the automobile within a foot of a large wall, with 25 feet of room to back up. Mark the wall with the masking tape along the vertical and horizontal axis points of the headlights. Start with a 6-foot strip of tape from the center point of the driver's side headlight to the center of the passenger's side light.

Then take two 6-inch pieces of tape and put a vertical mark in front of each light, creating a cross-shaped mark that will act as a bull's eye. Back the auto up 25 feet. Turn the HID headlights on so that they shine against the wall. Inspect the light beams. Both headlights should land 2 inches below the 6-foot strip of tape. The passenger's side headlight should also land directly on the shorter strip, but the driver's side should hit 2 inches to the right.

This indicates that the beam will not hit oncoming traffic. Open the hood and go to the rear of the headlight assembly. At the top and center of the headlight will be a small adjusting screw that controls the light's vertical axis. Use a screwdriver to adjust this until the light hits the desired spot.

Along one of the sides will be a second screw for the horizontal axis. Adjust this screw as well. Steve Bradley is an educator and writer with more than 12 years of experience in both fields. He maintains a career as an English teacher, also owning and operating a resume-writing business. Bradley has experience in retail, fashion, marketing, management and fitness. He holds a Bachelor of Arts in English and classics.

Step 1 Load the automobile with enough weight to approximate the normal nighttime driving weight. Step 2 Pull the automobile within a foot of a large wall, with 25 feet of room to back up.

Step 3 Back the auto up 25 feet. Masking tape Screwdriver Assistant.

0 thoughts on “How to adjust hid headlights

Add a comment

Your email will not be published. Required fields are marked *